UNS N06625

Inconel 625

Nickel-chromium-molybdenum-niobium alloy for corrosion-resistant equipment and components requiring useful strength without precipitation hardening.

Alloy 625 supply and ordering

Start with UNS N06625, the product form, and the standard edition on your purchase specification. Include dimensions, quantity, delivery condition, and document requirements so the quotation can identify the material and inspection requirements for your order.

Published catalog ranges and conditions are reference entries. The quotation confirms exact sizes, tolerances, delivery condition, availability, and documents for your order.

FormStandard referenceCatalog dimensionsCatalog conditionRequest a quote
Bar / RodASTM B446 (2023)Quote to confirmQuote to confirmGet quote
PlateASTM B443 (2023)3-60 mm thickSolution annealedGet quote
Seamless Pipe / TubeASTM B444 (2023)6-219 mm ODSolution annealedGet quote
Forged ProductASTM B564 (2023)Up to 3000 mm / 5 tSolution annealedGet quote

What dimensions should I send for bar or plate?

For bar or rod, specify the diameter or cross-section, length, tolerances and surface finish. For plate, specify the thickness, width and length, plus any flatness or cutting requirements. Include the quantity and destination for either form.

Which standard and condition go on the RFQ?

ASTM B446 covers rod and bar, and ASTM B443 covers plate, sheet and strip. Include the edition, heat-treatment condition and any supplementary requirements specified by your project. Ask the buyer or technical team to confirm the required edition and condition if the order documents do not specify them. See the Special Metals Alloy 625 technical bulletin for the form-to-standard references.

How do I specify material certificates or inspection?

State the required certificate or test report and any heat or lot traceability, marking, or third-party inspection requirements in your RFQ. The order documents should identify what is agreed for the requested form and condition.

Grade selection profile

Select against the service temperature, medium, loading and applicable specification. A shared material system does not make grades or process routes interchangeable.

Material overview

Nickel-chromium-molybdenum-niobium alloy for corrosion-resistant equipment and components requiring useful strength without precipitation hardening. Typical uses include marine and seawater components, chemical processing, oil and gas, flue-gas desulfurization. For a quotation, identify the required product form, dimensions, delivery condition and applicable material specification. Compare the service medium, temperature and loading with the required manufacturing and heat-treatment route before final grade selection.

Key characteristics

  • Resists pitting, crevice corrosion and chloride stress-corrosion cracking
  • high fatigue strength
  • oxidation to ~980 C
  • no age hardening required

Typical applications

  • Marine and seawater components
  • chemical processing
  • oil and gas
  • flue-gas desulfurization
  • reactor components

Grade names and equivalents

Alloy 625Common nameNS3306EquivalentNCr22Mo9NbEquivalent

Technical properties

Typical values are for reference only. Final chemistry, mechanical properties, heat treatment, dimensions, inspection, and documentation are confirmed against the applicable specification and MTC/COA before order acceptance.

Chemical composition

PropertyValueUnitCondition / standard
Ni58.0 minwt%Typical value
Cr20.0-23.0wt%Typical value
Mo8.0-10.0wt%Typical value
Nb3.15-4.15wt%Typical value
Fe5.0 maxwt%Typical value
C0.10 maxwt%Typical value
Mn0.5 maxwt%Typical value
Si0.5 maxwt%Typical value
Al0.4 maxwt%Typical value
Ti0.4 maxwt%Typical value

Mechanical properties

PropertyValueUnitCondition / standard
Tensile strengthmin 827MPaSolution annealed
Yield strength 0.2%min 414MPaSolution annealed
Elongationmin 30%Solution annealed
Hardnessmax 217HBSolution annealed

Physical properties

PropertyValueUnitCondition / standard
Density8.44g/cm3Typical
Melting range1290-1350CTypical

Standards and specifications

ASTM B446 (2023)Standard Specification for Nickel-Chromium-Molybdenum-Columbium Alloy (UNS N06625) Rod and BarASTM B443 (2023)Standard Specification for Nickel-Chromium-Molybdenum-Columbium Alloy (UNS N06625) Plate, Sheet, and StripASTM B444 (2023)Standard Specification for Nickel-Chromium-Molybdenum-Columbium Alloy (UNS N06625) Seamless Pipe and TubeASTM B564 (2023)Standard Specification for Nickel Alloy ForgingsGB/T 15007 (2017)Specification for Nickel and Nickel Alloy Wrought Products

Capabilities